Series #1-10 ตอบคำถาม "ทำงาน X อย่างไร" สำหรับแต่ละ application — แต่บทความนี้ตอบคำถามต่างกัน: "งาน X ใช้ method ไหน?" · บทความนี้คือ decision framework สำหรับ Maintenance Planner ที่ต้อง mapping จาก task → method → equipment ใน CMMS · 3 จุด focus: (1) Coil vs Glow Cable vs HF เมื่อไหร่ใช้อะไร, (2) Skin Depth Physics + Power Calculation สำหรับ rough sizing, (3) 4-Question Decision Tree ที่ใช้ได้ทุก case
1️⃣ Killer Concept #1 — Coil vs Glow Cable vs HF
3 method หลักที่เลือกใน 90% ของงาน maintenance:
Rigid Coil
Solid copper coil ออกแบบเฉพาะ component geometry · efficiency สูงสุด · repeatable
เหมาะ: bearing inner race · pin · bushing · sheave hub · thrust collar · shrink fit small-medium part
Trade-off: ต้องออกแบบเฉพาะ · cost upfront สูง · เหมาะ production repeated
Glow Cable
Flexible inductor 30 ม. wrap รอบ component · field deployment · irregular geometry
เหมาะ: pipe spool · vessel section · slewing ring 1-5 ม. · local PWHT · large diameter
Trade-off: efficiency ต่ำกว่า rigid coil 10-20% · flexibility ชดเชย
HF Generator
High Frequency 50-400 kHz + close coupling · paramagnetic alloy + thin wall
เหมาะ: SS/Inconel/Ti · centrifugal impeller · thin wall section · surface heating
Trade-off: heat penetration shallow · complex tuning · ต้อง gap < 5 mm บางครั้ง
2️⃣ Killer Concept #2 — Skin Depth Physics + Power Calc
Skin Depth Formula:
δ = skin depth (mm) · ρ = electrical resistivity (Ω·m) · μᵣ = relative permeability · f = frequency (Hz)
ตัวอย่าง carbon steel ที่อุณหภูมิห้อง (ρ ≈ 1.7×10⁻⁷, μᵣ ≈ 100):
ที่ 10 kHz: δ ≈ 6.6 mm · ที่ 100 kHz: δ ≈ 2.1 mm
Power Requirement (rough estimate):
P = power (kW) · m = mass (kg) · cp = specific heat (kJ/kg·K) · ΔT = temp rise · η = efficiency (0.5-0.85) · t = heat-up time (s)
ตัวอย่าง: heat 50 kg steel from 20→200°C ใน 600s, η=0.7:
P = 50 × 0.46 × 180 / (0.7 × 600) = ~9.9 kW
เลือก generator ≥ 1.3-1.5× คำนวณ → 15 kW safety margin
Skin Depth ตาม Material + Frequency
| Material | 10 kHz | 30 kHz | 100 kHz | 300 kHz |
|---|---|---|---|---|
| Carbon Steel (room T) | 6.6 mm | 3.8 mm | 2.1 mm | 1.2 mm |
| Carbon Steel (above Curie) | 66 mm | 38 mm | 21 mm | 12 mm |
| SS 304/316 | 36 mm | 21 mm | 11 mm | 6.6 mm |
| Inconel 625 | 57 mm | 33 mm | 18 mm | 10 mm |
| Titanium Ti-6Al-4V | 66 mm | 38 mm | 21 mm | 12 mm |
| Copper (heat sink) | 0.66 mm | 0.38 mm | 0.21 mm | 0.12 mm |
3️⃣ Killer Concept #3 — 4-Question Decision Tree
📋 Application → Method Decision (4 Questions)
4️⃣ Series #1-10 Map — Where to Read Detail
บทความนี้เป็น decision-level — รายละเอียดของแต่ละ application อยู่ที่ Series #1-10:
5️⃣ Application → Method Quick Reference Table
| Application | Method | Frequency | Detail Article |
|---|---|---|---|
| Bearing removal/install | Rigid Coil | MF 10-30 kHz | Series #1 |
| Shrink fit coupling | Rigid Coil | MF 10-30 kHz | Series #2 |
| PWHT pipeline | Glow Cable | MF 5-15 kHz | Series #3 |
| Turbine rotor | Rigid Coil | MF 5-30 kHz | Series #4 |
| Hot bolting | Rigid Coil | MF 10-30 kHz | Series #5 |
| Local stress relief | Glow Cable | MF 5-15 kHz | Series #6 |
| Pipeline tie-in | Glow Cable | MF 5-15 kHz | Series #7 |
| Heat exchanger tube | Rigid Coil | MF 10-50 kHz | Series #8 |
| Slewing ring crane | Glow Cable | MF 5-15 kHz | Series #9 |
| Subsea Inconel/Ti | Custom Coil | HF 50-400 kHz | Series #10 |
Equipment Reference
📚 eldec Equipment Range Mapping
เพื่อไม่ซ้ำเนื้อหา — สำหรับ generator core specs ดูที่ Series #1: Bearing Removal
eldec lineup map: PICO Series (5-25 kW · small portable bolt + bearing) · ECO-LINE EEI² XS-XL (5-150 kW · industrial general) · CUSTOM-LINE / RACK-LINE (200-1000 kW · large customized) · เลือกตาม power calculation Q4 · ดูรายละเอียด eldec Induction Generator + eldec PICO vs ECO-LINE